Hylosil 310 Red High-temperature RTV silicone sealant 300ml cartridge

Hylosil Silicone Sealant 310 is a Room Temperature Vulcanising (RTV) silicone sealant which has been specifically developed for high temperature applications. Once applied the compound reacts
with atmospheric moisture to form a tough and durable rubber seal. It has excellent adhesion to metals, glass, ceramics and plastics. The compound has large gap filling properties which makes it
ideal for application to non-machined surfaces and even as cast surfaces.

Hylosil RTV Silicone Sealant 310 is resistant to oil, water and lubricants and will remain flexible to withstand vibration

Typical Properties, Uncured Product

• Colour : Brick Red
• Consistency : Non-slump paste
• Cross Linking System : Acetoxy
• Specific Gravity (DIN 53479) : 1.21-1.29
• Solids Content : 100%
• Extrusion Rate 3mm orifice @ 60 psi (BS 3712: Part 1) : 78 g/minute
• Skin Forming Time at 230C (73.40F) /50% RH (BS 5889) : 15 minutes
• Cure Rate @ 250C(770F) and 60% RH : 3mm per 24 hours
• Volume: 300ml (10.14fl.oz) cartridges

Cured Product

• Tensile Strength DIN 53505, S3A : 1.4 N/mm²
• Elongation @ Break DIN 53504, S3A : 420%
• E Modulus @ 100% Elongation DIN 53504, S3A : 0.6 N/mm²
• Hardness Shore A DIN 53505 : 43°
• Tear Strength ASTM D 624, Form B: 7 N/mm²
• Shrinkage DIN 53504, S3A : 3%
• Typical temperature Range : -500C to 3000C(-580 to 5720F)
• Ignition Temperature : DIN 51794 4600C (8600F)

Typical Applications
Hylomar Silicone Sealant 310 is a general purpose adhesive sealant with many applications in building, engineering and the automotive industry. It has excellent adhesion without primer to
metals, glass, ceramics and most rigid plastics. The cured compound is resistant to weathering, aging and to many solvents, oil, water and lubricants. Its excellent thermal stability means it can be
used for sealing and bonding at temperatures up to 3000C (5720F) and for gasketing up to 3500C (6620F) depending on the application. It is ideal for use as a flexible gasket or flange sealant in
automotive and general engineering applications. 

Handling and Safety Properties
Please see product safety data sheet.

Packaging
Hylomar Silicone Sealant 310 is available in 85g (3oz) tubes, 300ml (10.14fl.oz) cartridges and 17 litre (574.84fl.oz) pails.
Storage
Product should be stored between 50C to 250C (410F to 770F).
 

Hazard Information (CLP)

Signal word: Danger

Hazard statements (H-phrases)

• H315: Causes skin irritation.
• H318: Causes serious eye damage.

Safety advice (P-statements)

Prevention:

• P264: Wash thoroughly after handling.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.

Response:

• P302+P352: IF ON SKIN: Wash with plenty of water.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P310: Immediately call a POISON CENTER or doctor.
• P332+P313: If skin irritation occurs: Get medical advice/attention.

Storage:

• Not assigned.

Disposal:

• Not assigned.

Other relevant information

• Hazardous ingredient: Triacetoxyethylsilane.
• No PBT/vPvB substances or endocrine disruptors present according to REACH.

 

Information on product safety (Manufacturer, Contact)

HYLOMAR GMBH, Talstraße 106, 41516 Grevenbroich, GERMANY, +49 2182 5708971, [email protected], www.hylomar.com/de