Delo-Photobond 4436 UV-curing acrylate adhesive tension-equalizing 1kg

Base

• modified acrylate
• One-component, solvent-free

Use

• Specifically developed for interior visual bondings, e. g., bonding of prisms for beamers-   high transparency and permanent light fastness
• Very good  capillary properties
• Easy processing at room lighting is possible
• The cured product is normally used in a temperature range of -40 °C to +120 °C; depending onthe application, other limits may be more reasonable
• Compliant with RoHS directive 2015/863/EUProcessing
• The adhesive is supplied ready for use; in case of cool storage, it must be ensured that thecontainer is conditioned to room temperature before use
• The containers are conditioned at room temperature (+18 °C to +25 °C); the conditioning time isapprox. 0.5 h for containers up to 50 ml and approx. 4 h for containers up to 1,000 ml; additional heat addition is not allowed-   the adhesive can be applied by dispensing
• The surfaces to be bonded must be dry as well as free of dust, grease and other contaminations
• Dispensing valves and product-bearing elements must be carefully cleaned before use,residues of other products must be completely removed; DELOTHEN EP as well as acetone,isopropanol or a mixture of both are recommended to remove DELO-PHOTOBOND residues
• For further information please refer to our instructions for use DELO-PHOTOBOND and thebrochure “Light Curing”Curing
• Curing with UV light in a wavelength range from 320 to 400 nm. DELOLUX LED curing lampsare especially suitable as per the chart below. All standard DELOLUX HID discharge lamps arealso suitable-   increased intensities shorten the required irradiation time, lower intensities prolong it.
• Size: 50g bottle

Technical specifications

• Tension-equalizing
• Suitable lamp types: LED 365 nm, LED 400 nm, UVA
• Color in uncured condition colorless
• Transparency transparent
• Color in cured condition in 0.1 mm layer thickness colorless
• Color in cured condition in 1 mm layer thickness colorless
• Density 1.0 g/cm³
• Viscosity (Liquid | Viscosimeter): 350 mPa·s
• Storage life in unopened original container (at 0 °C to +10 °C ): 12 months

Hazards Information (CLP)

Hazard statements (H phrases)

• H315: Causes skin irritation.
• H317: May cause an allergic skin reaction.
• H319: Causes serious eye irritation.
• H335: May cause respiratory irritation.
• H400: Very toxic to aquatic life.
• H410: Very toxic to aquatic life with long-lasting effects.

Precautionary statements (P phrases)

Prevention:

• P280: Wear protective gloves. Recommended: Viton® fluor rubber (1-4 hours breakthrough time). For short-term exposure (< 15 minutes): nitrile gloves.
• P280: Wear eye or face protection.
• P273: Avoid release to the environment.
• P261: Avoid breathing vapors.
• P264: Wash hands thoroughly after handling.

Response:

• P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing. If unwell, consult a poison center or doctor.
• P362+P364: Take off contaminated clothing and wash before reuse.
• P302+P352: IF ON SKIN: Wash with plenty of water.
• P333+P313: If skin irritation or rash occurs: Get medical advice/attention.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337+P313: If eye irritation persists: Get medical advice/attention.

Storage and disposal

• P403: Store in a well-ventilated place.
• P233: Keep container tightly closed.
• P501: Dispose of contents/container in accordance with local/regional/national/international regulations.

Other relevant information

• The product is classified as hazardous according to Regulation (EC) No 1272/2008.
• The mixture contains no substances assessed as PBT or vPvB.

DELO Industrie Klebstoffe GmbH & Co. KGaA, DELO-Allee 1, 86949 Windach, GERMANY, +49 8193 9900-0, [email protected], www.delo.de